提交测试

app/stm32fxxx_app/app/bmu_adbms1818.c

@@ -103,7 +103,7 @@ void bmu_config_init(void)
 	drv_gpio_set_pin_status(kGpioType_SP1_Cs_En2, kGpioStatus_Low);
 	//drv_gpio_set_pin_status(kGpioType_SP1_Cs_En1, kGpioStatus_Low);
 	bmu_data.bmu_num = get_eeprom_data(kEep_DevAddr_SlaverNum, kEepromDataType_Low);
-	//bmu_data.bmu_num = 2;
+	//bmu_data.bmu_num = 1;
 	if (bmu_data.bmu_num > BMU_MAX_NUM || bmu_data.bmu_num == 0)
 	{
 		bmu_data.bmu_num = BMU_MAX_NUM;
@@ -115,8 +115,8 @@ void bmu_config_init(void)
 	bmu_data.total_cell_num = get_eeprom_data(kEep_CellNum, kEepromDataType_Full);
 	bmu_data.total_temp_num = get_eeprom_data(kEep_TempNum, kEepromDataType_Full);
 	
-	//bmu_data.total_cell_num = 32;
-	//bmu_data.total_temp_num = 18;
+	//bmu_data.total_cell_num = 16;
+	//bmu_data.total_temp_num = 8;
 	
 	//set num from hmi =>adapt num for furture
 	cell_num = bmu_data.total_cell_num / bmu_data.bmu_num;
@@ -241,6 +241,7 @@ void bmu_vlot_breakline_check()
 }
 
 static int tempJudge_cnt[26][9] = {0};
+//static int tempCellErr_cnt = 0;
 //@wkun the here can add temp line break or connect
 void bmu_temp_breakline_check(int value, int bmuIdx, int tempIdx)
 {
@@ -445,6 +446,7 @@ void bms_poll_bmu(uint32_t base_time)
 	bmu_data_handler(base_time);
 	
 	//温感检测是否脱落，加上了防抖，需要两次大于6000，才设置温感排线错误，温感排线错误显示的有点慢
+	//温感的值最开始全是大于6000的，第二次才是采集值
 	memset(tempJudge_cnt, 0, sizeof(tempJudge_cnt));
 	//2-5 @wangk add this line bcu statistic data is show
 	bms_poll_statistic(0);

app/stm32fxxx_app/app/bmu_adbms1818.h

@@ -20,6 +20,9 @@ extern "C" {
 #include "statistic_manager.h"
 #include "run_status.h"
 #include "logic_ctrl.h"
+#include "bmu_manager.h"
+#include "string.h"
+#include "stdio.h"
 
 typedef struct
 {

app/stm32fxxx_app/app/soc_calculate.c

@@ -372,7 +372,7 @@ void soc_exterme_calibrate(int16_t current, uint16_t base_time)
 			if (((bms_get_statistic_data(kStatisticData_MinVolt) <= get_eeprom_data(kEep_FullDisVolt, kEepromDataType_Full))
 			 && (avg_volt <= get_eeprom_data(kEep_FullDisAvgVolt, kEepromDataType_Full))
 			 && (bms_get_ex_data(kExType_CellVolt) == kExStatus_None))
-             || (total_volt <= get_eeprom_data(kEep_FullDisTotalVolt, kEepromDataType_Full))
+             || (total_volt <= get_eeprom_data(kEep_FullDisTotalVolt, kEepromDataType_Full)/100)
              || ((sox_item.soc_req_st == kSocStatus_Empty) && (sox_item.is_bsu_adjust == false)))
 			{
                 full_dly = 0;
@@ -465,8 +465,8 @@ void bms_init_soc(void)
     uint64_t tmp_64u;
 	  int32_t  year, mon, day;
     
-	soc = get_eeprom_data(kEep_SOC, kEepromDataType_Full);
-    //soc = bms_check_pwr_on_ocv(soc);
+	//soc = get_eeprom_data(kEep_SOC, kEepromDataType_Full);
+    soc = bms_check_pwr_on_ocv(soc);
     sox_item.soc_kEep_99 = true;
     sox_item.soc_kEep_1 = true;
     if (soc == 0)

app/stm32fxxx_app/app/task_register.c

@@ -59,7 +59,8 @@ void task_100ms_handler(uint32_t base_time)
 	static uint32_t cout100ms = 0;
 	cout100ms++;
     bms_poll_iso(base_time);
-    //bms_poll_adc(base_time);
+	//bms_poll_adc(); THis was originally commented.
+    bms_poll_adc(base_time);
     bms_poll_statistic(base_time);
 	bms_poll_run_status(base_time); 
     bms_poll_sop(base_time);
@@ -99,6 +100,7 @@ void poll_1ms_task_init(void)
 
 	bms_init_gpio();
     bms_init_eeprom();
+	//bms_init_adc(); THis was originally commented.
     //bms_init_adc();
     bms_init_tag();
     bms_init_run();
@@ -148,7 +150,8 @@ void poll_10ms_task_init(void)
 	drv_misc_cfg_pwr_off_interrupt(APP_CFG_INT_PRIO_PWR_OFF, kPwrOffVolt_2_9, bms_pwr_off_save);
     
     KIT_SET_BIT_MASK_32(is_data_ok, BMU_FINISH_BIT);
-    //while(KIT_GET_BIT_32(is_data_ok, SIGNAL_FINISH_BIT) == 0)
+	//next line is originally commented.
+    while(KIT_GET_BIT_32(is_data_ok, SIGNAL_FINISH_BIT) == 0)
     {
         bsp_task_delay_ms(10);
     }
@@ -158,7 +161,8 @@ void poll_10ms_task_init(void)
 
     bms_init_sop();
     bms_init_iso();
-    //bsp_create_task(&poll_100ms_task, (uint8_t *)"100ms");
+	//bsp_create_task(&poll_100ms_task, (uint8_t *)"100ms");,THis was originally commented.
+    bsp_create_task(&poll_100ms_task, (uint8_t *)"100ms");
 	bsp_create_task(&bms_poll_bmu_task, (uint8_t *)"100ms");
     bsp_create_task(&ord_comm_can_task, (uint8_t *)"100ms");
 	bsp_create_task(&modbus_rtu_task1, (uint8_t *)"inter_modbus");

app/stm32fxxx_app/prj/BCU_APP.uvprojx

@@ -786,6 +786,11 @@
               <FileType>1</FileType>
               <FilePath>..\app\fault_manager.c</FilePath>
             </File>
+            <File>
+              <FileName>ocv_tables.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\app\ocv_tables.c</FilePath>
+            </File>
             <File>
               <FileName>fault_register.c</FileName>
               <FileType>1</FileType>
@@ -831,11 +836,6 @@
               <FileType>1</FileType>
               <FilePath>..\app\logic_same_circuit_ctrl.c</FilePath>
             </File>
-            <File>
-              <FileName>ocv_tables.c</FileName>
-              <FileType>1</FileType>
-              <FilePath>..\app\ocv_tables.c</FilePath>
-            </File>
             <File>
               <FileName>run_status.c</FileName>
               <FileType>1</FileType>
@@ -1743,6 +1743,11 @@
               <FileType>1</FileType>
               <FilePath>..\app\fault_manager.c</FilePath>
             </File>
+            <File>
+              <FileName>ocv_tables.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\app\ocv_tables.c</FilePath>
+            </File>
             <File>
               <FileName>fault_register.c</FileName>
               <FileType>1</FileType>
@@ -1788,11 +1793,6 @@
               <FileType>1</FileType>
               <FilePath>..\app\logic_same_circuit_ctrl.c</FilePath>
             </File>
-            <File>
-              <FileName>ocv_tables.c</FileName>
-              <FileType>1</FileType>
-              <FilePath>..\app\ocv_tables.c</FilePath>
-            </File>
             <File>
               <FileName>run_status.c</FileName>
               <FileType>1</FileType>